top of page

Draft Load Sensing Pin Elimination Kit McCormick

WE-40510010-2

Draft Load Sensing Pin Elimination Kit McCormick

USD 60.95

$160.00

average rating is 3 out of 5

WE-40510010 Draft Load Sensing Pin Elimination Kit

 

Includes:

(2) Modules, (4) Tie Wraps & Installation Instructions

Replaces Part #:

1964916C1, 1964916C3, 305135A1, 403057A3, 403057A1, 6521562M1

 

Purpose:

This module kit is used to eliminate the need for the factory load sensing pin to be connected and allow manual use of the 3-point hitch. This module kit will eliminate the draft sensing function of the tractor completely so that the diagnostic system will not detect defective pins.

 

Fitment:

Case IH: 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 8910, 8920, 8930, 8940, 8950, 9110, 9130, 9150, 9210, 9230, 9240, 9250, 9260, 9310, 9330, 9350, CX100, CX50, CX60, CX70, CX80, CX90, MX100, MX100C, MX110, MX120, MX135, MX150, MX170, MX90C

 

McCormick: MC100, MC105, MC110, MC115, MC120, MC125, MC130, MC135, MC80, MC90, MC95, MTX110, MTX120, MTX125, MTX135, MTX140, MTX145, MTX150, MTX155, MTX165, MTX175, MTX185, MTX200

 

Steiger: 9110, 9130, 9150, 9210, 9230, 9240, 9250, 9260, 9310, 9330, 9350

 

Note: Will not work on following models if equipped with older style round threaded connections:

7110, 7120, 7130, 7140, 7150. Order (2) WE-40510012 harness adapters

Note: Only fits the following models with S/N JCB0003600 & After, if equipped with draft control:

9110, 9130, & 9150

 

Installation Guide:

  • Locate the wiring harness for both sensor pins and locate where sensor pin harness is plugged into tractor harness. Connectors are located under the rear of cab on the forward side of the three-point hitch housing. Note there are two harnesses that will be disconnected.
  • Unplug both sensor pin harness and plug replacement 830485WE module into tractor side harness.
  • Using the supplied 8” plastic ties, secure the load sensing elimination modules to prevent damage during movement of tractor mechanical linkages and hitch arms.
  • After replacement with load sensing elimination modules the hitch controls will only function in manual mode with no draft control functionality.

Color *

Selected color

Make

McCormick

Category

3 Point Hitch

Models

MC100, MC105, MC110, MC115, MC120, MC125, MC130, MC135, MC80, MC90, MC95, MTX110, MTX120, MTX125, MTX135, MTX140, MTX145, MTX150, MTX155, MTX165, MTX175, MTX185, MTX200

Replaces Part #

1964916C1, 1964916C3, 305135A1, 830485

Tech Info

This module kit is used to eliminate the need for the factory load sensing pin to be connected and allow manual use of the 3-point hitch. This module kit will eliminate the draft sensing function of the tractor completely so that the diagnostic system will not detect defective pins.Will not work on following models if equipped with older style round threaded connections: 7110, 7120, 7130, 7140, 7150. Must order WE-2550012 in addition to the WE-2550010 elimination kit to use on the older style round threaded connectors

Industry

Agricultural

Product Information

WE-40510010 Draft Load Sensing Pin Elimination Kit

 

Includes:

(2) Modules, (4) Tie Wraps & Installation Instructions

Replaces Part #:

1964916C1, 1964916C3, 305135A1, 403057A3, 403057A1, 6521562M1

 

Purpose:

This module kit is used to eliminate the need for the factory load sensing pin to be connected and allow manual use of the 3-point hitch. This module kit will eliminate the draft sensing function of the tractor completely so that the diagnostic system will not detect defective pins.

 

Fitment:

Case IH: 7110, 7120, 7130, 7140, 7150, 7210, 7220, 7230, 7240, 7250, 8910, 8920, 8930, 8940, 8950, 9110, 9130, 9150, 9210, 9230, 9240, 9250, 9260, 9310, 9330, 9350, CX100, CX50, CX60, CX70, CX80, CX90, MX100, MX100C, MX110, MX120, MX135, MX150, MX170, MX90C

 

McCormick: MC100, MC105, MC110, MC115, MC120, MC125, MC130, MC135, MC80, MC90, MC95, MTX110, MTX120, MTX125, MTX135, MTX140, MTX145, MTX150, MTX155, MTX165, MTX175, MTX185, MTX200

 

Steiger: 9110, 9130, 9150, 9210, 9230, 9240, 9250, 9260, 9310, 9330, 9350

 

Note: Will not work on following models if equipped with older style round threaded connections:

7110, 7120, 7130, 7140, 7150. Order (2) WE-40510012 harness adapters

Note: Only fits the following models with S/N JCB0003600 & After, if equipped with draft control:

9110, 9130, & 9150

 

Installation Guide:

  • Locate the wiring harness for both sensor pins and locate where sensor pin harness is plugged into tractor harness. Connectors are located under the rear of cab on the forward side of the three-point hitch housing. Note there are two harnesses that will be disconnected.
  • Unplug both sensor pin harness and plug replacement 830485WE module into tractor side harness.
  • Using the supplied 8” plastic ties, secure the load sensing elimination modules to prevent damage during movement of tractor mechanical linkages and hitch arms.
  • After replacement with load sensing elimination modules the hitch controls will only function in manual mode with no draft control functionality.

No product information

Reviews

average rating is null out of 5

8/10/2024

undefined

Load More

4.7

average rating is null out of 5

Based on 100 Reviews

Recently Viewed

Product Name

USD 39.95

Product Name

USD 39.95

Product Name

USD 39.95

Product Name

USD 39.95

bottom of page